Browse New, Used, and Rebuilt Inventory in Stock
Results for: V Blender
| Condition | Model | S/N | Description | Delivery |
|---|---|---|---|---|
| NEW | DPM-1QT Double Planetary Mixer BatchChange Can | Air/oil reverse hydraulic lift, vacuum capability, high-viscosity (HV) blades with 150-grit finish, 1/2 HP explosion-proof motor, T316 flexi-lip sealed gearbox, two 2" sight/charge ports, Viton seals, can-hood clamps, internally machined Mix Can, 50 psig jacket, thermowell, NEMA 12, 3-phase, 60 Hz, 230V, 4" color touchscreen display with start/stop, speed control, speed, load, temperature, cycle timer, speed and temp calibration, E-stop, fused rotary disconnect, leveling mounts. | 8-10 WEEKS | |
| NEW | DPM-2 Double Planetary Mixer BatchChange Can | Air/oil hydraulic lift with two-hand safety controls for the lift, vacuum capability, high viscosity (HV) blades, 1.5 HP explosion-proof motor, 3-phase, 60 Hz, 230V, inverter drive, T316 stainless steel with 80-grit finish, Viton seals, sealed flexi-lip gearbox, (2) 3" ports, 50 psig stainless steel jacketed mix can with internal machining and thermowell, 1" ball valve, casters for mobility, hood-can clamps, NEMA 12 rated control panel, 3-phase, 60 Hz, 230V, 4" color touchscreen display with speed, load, time, temperature, start/stop, E-stop, fused rotary disconnects, full calibration capabilities, fully mounted and wired, leveling pads. | 8-10 WEEKS | |
| NEW | DPM-2 Double Planetary Mixer BatchChange Can | Air/oil hydraulic lift with two-hand safety controls, vacuum capability, high-viscosity (HV) blades, 1.5 HP explosion-proof motor, 3-phase, 60 Hz, 230V, inverter drive, T316 stainless steel with 80-grit finish, Viton seals, sealed flexi-lip gearbox, two 3" ports, hood-can clamps, 50 psig stainless steel jacketed mix can, internal machining, thermowell, 1" ball valve, casters. Bench with leveling pads. | 8-10 WEEKS | |
| NEW | DPM-4 Double Planetary Mixer BatchChange Can | Air/oil hydraulic lift with two-hand controls, T316 parts, 80-grit finish, vacuum capability, high-viscosity (HV) blades, 2 HP explosion-proof motor, 3-phase, 60 Hz, 230V, inverter drive, Viton seals, sealed flexi-lip gearbox, two 3" ports, hood-can clamps, 50 psig sidewall and bottom jacket, thermocouple, 1" tri-clamp ball valve, casters, NEMA 12 control panel, 3-phase, 60 Hz, 230V, 4" mounted and wired color touchscreen display with speed, load, time, temperature, E-stop, disconnect. Painted bench with leveling mounts. | 8-10 WEEKS | |
| RECON | DPM-2 Double Planetary Mixer BatchChange Can | 210899 | Air/oil hydraulic lift with two-hand safety controls, vacuum capability, 1.5 HP TEFC motor, 3-phase, 60 Hz, 230V, inverter drive, high-viscosity (HV) blades, T304 stainless steel, 80-grit finish, viton seals, sealed flexi-lip gearbox, two 3" CB ports, 100 psig stainless steel jacketed mix can, internally machined, thermowell, 1.25" cove plug valve, casters, hood-can clamps, NEMA 12 control panel, 1.5 HP VFD, 3-phase, 60 Hz, 230V. Bench with casters. | 3-4 WEEKS |
| RECON | DPM-5 Double Planetary Mixer BatchChange Can | 116102 | GEN FEAT: Air/oil hyd lift. Vac rated. T316 wetted, 240 int. T304 ext, 80-grit. EPDM/Teflon. CE marked. AGITATORS/DRIVE: Two (2) sets of HV blades. Sidewall scraper. 3HP CE ATEX Zone 21 3ph/50Hz/400V motor. Flexi lip agitator shaft seals. Dust sheild. VACUUM HOOD: Two (2) 3" TC sight/charge ports w/ metaglass. LED tank light. One (1) 1" TC vac port. Hood to bonnet quick release clamps. EPDM oring. MIX CANS: Two (2) Vac rated T316. Hood to can clamps. Rated for discharge. 240 int / 80 ext. 1-1/4" ACME thread cove plug w/ EPDM oring. 50psig jacket. Type-J thermo. SS casters. TRANSPORT COVERS: Two (2), vapor tight, EPDM oring, clamps. VAC PUMP: 0.75hp CE ATEX Zone 21. Mounted on lower shelf (controls located in panel). CONTROLS: NEMA 4X, SS, Type X purge, 3/50/400V. PLC for 10 recipes. Shipped loose. MIXER BENCH: T304 80-grit. Casters. Enclosed T304 sheathing. Alignment pins. TRANSFER CARTS: Two (2) T304 80-grit, casters, alignment pins. CE Certified. | 4-WEEKS |
| RECON | HDM-10 Double Planetary Mixer BatchChange Can | 58317 | Air/oil hydraulic lift with foot valve, 5 HP mechanical vari-drive, vacuum (retrofit), T304 vacuum hood, 80-grit interior and exterior finish, Viton seals, T304 rectangular stirrer blades, cast iron gearbox (painted), mix can, vacuum-rated, 15 psig, trunnions, 2" ball valve, casters, type-J mini thermowell. | 2-3 WEEKS |
| RECON | HDM-100 Double Planetary Mixer BatchChange Can | 53582 | Air/oil hydraulic lift, vacuum hood, stainless steel T304, dust shield, Viton elastomers, rectangular stirrers, 30 HP TEFC motor, 3-phase, 60 Hz, 230/460 V, one 1" FNPT vacuum exhaust port, two 3" sight/charge ports (Cherry Burrell style), two vacuum T304 mix cans, 15 psig carbon jacket, 2" ball valve located in center, casters. | 18-20 WEEKS |
| RECON | HDM-200 Double Planetary Mixer BatchChange Can | 21933 | Air/oil hydraulic lift, non-vacuum design, Viton seals, rectangular stirrer blades, sidewall scraper, 40 HP explosion proof vari-drive, cast iron gearbox, mechanical shaft seals, dust shield, two 3" sight/charge ports, one 6" sight/charge port, one 1" NPT, 200-gallon stainless steel T304 mix can, 80-grit finish, 50 psig carbon steel jacket, trunnions, 2" ball valve. | 18-20 WEEKS |
| NEW | PDM-2 Power Mix Planetary Disperser Planetary Mixer Batch Change Can | Air/oil reverse lift, stainless steel T304, vacuum design, 80-grit finish, Viton seals, 1 HP explosion proof planetary blade, 1.5 HP explosion proof disperser with 3" high speed disperser blade, side and bottom scrapers, stainless steel gearbox with Kalrez seal O-rings, three 3" tri-clamp sight/charge ports with Metaglass, two 1/2" NPT ports, hood-to-bonnet quick disconnect clamps, vacuum-rated mix can, 50 psig stainless steel jacket, internally machined, thermowell, 1-1/4" cove plug valve, casters, hood-can clamps. | 8-10 WEEKS | |
| NEW | PDM-40 Power Mix Planetary Disperser Planetary Mixer Batch Change Can | Air/oil lift, vacuum design, Viton seals, stainless steel T316 construction, 80-grit finish, 7.5 HP explosion proof planetary stirrer, 15 HP explosion proof disperser, carbon steel gearbox with Viton gaskets, one 1" NPT port, and two 3" sight/charge ports, stainless steel mix can, 2" ball valve, casters, 50 psig stainless steel jacket, RTD thermowell. | TBD | |
| NEW | PDDM-10 Power Mix Planetary Disperser Planetary Mixer Batch Change Can | 117635 | Air/oil lift, vacuum design, stainless steel T304, 150/80-grit finish, silicone/Teflon encapsulated silicone seals, two 5 HP explosion proof high-viscosity stirrers, two 15 HP explosion proof dispersers with 4-1/2" high speed disperser blades, stainless steel sealed gearbox, one 6" tri-clamp port, one 1" NPT, two 3" tri-clamp sight/charge ports with Metaglass, mix can with 50 psig stainless steel jacket, internally machined, type-J thermowell, 2" ball valve, casters. | STOCK |
| RECON | PDM-1/2 Power Mix Planetary Disperser Planetary Mixer Batch Change Can | 218165 | Air/oil reverse lift, vacuum design, stainless steel T316, 80-grit finish, silicone seals, 1/2 HP TEFC planetary mixer, 1 HP TEFC disperser with 2" high speed disperser blade, stainless steel sealed gearbox with Viton O-rings, two 2" sight/charge ports, one 1/2" NPT port, vacuum-rated mix can, 50 psig stainless steel jacket, hood-can clamps, NEMA 12 rated control panel, 3-phase, 60 Hz, 230 V, 7" color touchscreen, cycle timer, temperature, E-stop, disconnect, mounted and wired. Bench with leveling pads. | 3 WEEKS |
| NEW | VMC-10 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | Stainless steel T316 construction, 80-grit interior and exterior, vacuum, Viton seals, 3 HP anchor with scrapers, 5 HP high shear mixer SLIM bushingless with large square hole stator, 5 HP disperser with 4-1/2" blade, 1" NPT port, two 3" sight/charge ports, RTD thermowell, 2" ball valve, casters. | 8-10 WEEKS | |
| NEW | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 117266 | Standard air/oil lift, stainless steel T316, 80-grit interior and exterior, vacuum, mechanical seals with Teflon/TES/Kalrez elastomers, 5 HP explosion proof three-wing anchor with scrapers (80 rpm), 5 HP explosion proof high shear mixer SLIM bushingless with large square hole stator (3600 rpm), 7.5 HP explosion proof disperser with 6" blade at 2550 rpm (4000 feet per minute), two 3" tri-clamp sight and charge ports with Metaglass, two 1-1/2" tri-clamp ports, mix can stainless steel 316, 50 psig stainless steel jacket, 2" ball valve, 80-grit finish, RTD thermowell, casters, four clamps. NEMA 7/9 junction box for motors and limit switches, NEMA 4 intrinsically safe junction box for thermocouple. | STOCK |
| NEW | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 113362 | ATEX explosion proof, all stainless steel, vacuum and 8 psig pressure capable, stainless steel T316 wetted surfaces, 150-grit interior, 80-grit exterior, mechanical seals with Kalrez and other elastomers EPDM, light curtain safety feature, full specifications upon request, 7.5 HP three-wing anchor drive with scrapers, two 5 HP bushingless SLIM rotor-stators with slotted heads, motors are ATEX Directive 94/9/EC Zone 1, 7.3 cubic feet stainless steel charge hopper with vibrator, two 3" sight/charge ports, one 1-1/2" tri-clamp port, one 1" tri-clamp port, one 1" FNPT vacuum port, two stainless steel T316 vacuum mix cans with 50 psig ASME code jackets and casters, 2" ball valve, RTD thermowell, 80-grit finish, NEMA 12 / IP52-rated control panel with remote control panel, current operating voltage 3-phase, 50Hz, 400V. Full specifications upon request. | STOCK |
| RECON | PVM-2 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 61541 | Electro/hydraulic lift, vacuum, stainless steel T304, 80-grit interior and exterior, Viton elastomers, 1/2 HP explosion proof three-wing anchor with fixed scrapers, 1 HP explosion proof high shear mixer, 1 HP explosion proof disperser, 10:1 speed range, two 2" sight/charge ports, two 1/2" NPT ports, thermoprobe, flexi seals, mix can with 50 psig jacket, 1" ball valve, type-J thermocouple, no casters, NEMA 12 rated control panel, 3-phase, 60 Hz, 230 V, 7" HMI, start/stop, speed, load, temperature, cycle, reversing lift motor starter for lift, two-hand push button raise/lower, E-stop, mounted and wired. | STOCK |
| RECON | PVM-10 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 58027 | Air/oil hydraulic lift, stainless steel T316 wetted parts, vacuum, 150-grit interior, 80-grit exterior, Viton seals, two 3" sight/charge ports, one 1" NPT port, thermoprobe in the vacuum cover type-J, 3 HP explosion proof anchor with hinged Teflon scrapers, 5 HP explosion proof high speed disperser, 1.5 HP explosion proof high shear mixer, mechanical seals, mix can, vacuum, stainless steel T316, 2" NPT ball valve, 15 psig stainless steel jacket, casters, safety pin in non-rotating device. Control panel: NEMA 12 enclosure designed for operation on 230 V, 3-phase, 60 Hz power supply. | STOCK |
| RECON | VMC-10 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 75331 | Air/oil hydraulic lift, stainless steel T304, vacuum and +5 psig internal pressure, 150-grit interior, 80-grit exterior, Viton seals, one 3" sight/charge port, one 1" NPT port, thermowell Type-J, 3 HP explosion proof anchor with hinged Teflon scrapers, 5 HP explosion proof 4.5" high speed disperser, 1.5 HP explosion proof high shear mixer, two mix cans with can-cover clamps, valve and casters, mechanical seals. VFD's - 3-phase 60Hz 460 V, shipped loose. | 4-WEEKS |
| RECON | VMC-10S Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch hsd. All Stainless Steel Ext. | 110666 | Dual Shaft Mixer, all stainless steel base, bonnet, enclosure with bellows, air/oil hydraulic lift, stainless steel T316, vacuum, 150-grit interior, 80-grit exterior, Viton seals, two 3" tri-clamp ports with Metaglass, one 1/2" NPT port, thermowell explosion proof (RTD), 3 HP explosion proof anchor (12�112 rpm) with hinged Teflon scrapers, 5 HP explosion proof 4.5" high speed disperser blade (430�4300 rpm), mix can, vacuum, stainless steel T316, 150-grit finish, 2" tri-clamp ball valve, casters, 50 psig stainless steel jacket. Control panel: NEMA 7/9, start/stop push buttons, speed potentiometers, speed display and load display for each drive, E-stop, intrinsic safety barrier for temperature, NEMA 12 panel with 5 HP and 3 HP variable frequency drives, disconnect, 3-phase, 60Hz, 480 V. | 3-4 WEEKS |
| RECON | VMC-10 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 108611 | Dual Shaft Mixer, air/oil hydraulic lift, stainless steel T304, vacuum, 80-grit interior & exterior, Viton seals, two 3" sight/charge ports, one 1" NPT port, thermowell type-J, 3 HP TEFC anchor (12�112 rpm) with hinged Teflon scrapers, 2 HP TEFC 3" propeller (100�1000 rpm), mix can, vacuum, stainless steel T304, 80-grit finish, 2" ball valve, casters (no jacket). NEMA 12, 3/60/230 V, start/stop push buttons and speed potentiometer for each drive, 6" color touchscreen with displays for speed, load, temperature, recipe system, data acquisition, Allen-Bradley PLC, E-stop, disconnect, 2 HP and 3 HP variable frequency drives. | STOCK |
| RECON | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 116825 | Air/oil hydraulic lift, stainless steel T316 construction, 80-grit interior and exterior finish, PTFE and Teflon-enclosed silicone seals with Chemraz elastomers, vacuum capability, 80 rpm, 5 HP explosion-proof anchor drive, 3-wing anchor with Teflon scrapers, 6" high-speed disperser blade with 7.5 HP explosion-proof motor, high-shear mixer with 5 HP explosion-proof motor, bushingless large square-hole stator with SLIM modification, one 1.5" tri-clamp port with ball valve, hose and wand, and funnel, mechanical seals with carbon vs. silicon carbide faces and Chemraz O-rings, vacuum cover with two 3" tri-clamp sight/charge ports with Metaglass TES gaskets, one RTD thermowell mounted on a 1.5" tri-clamp port, port light, two 1.5" tri-clamp ports, two 2.5" tri-clamp ports with spray nozzles, and one 1" tri-clamp port, mix can fabricated from stainless steel T316 with 80-grit interior and exterior finish, 2" tri-clamp ball valve, 50 psig stainless steel T304 jacket on side and bottom, casters and clamps, NEMA 12 control panel, 3-phase, 60 Hz, 208�230 V. | 2 WEEKS |
| RECON | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 117258 | Air/oil hydraulic lift, stainless steel T316, 80-grit interior and exterior finish, PTFE and Teflon-enclosed silicone seals with Chemraz elastomers, explosion-proof design, vacuum capability, 3-wing anchor agitator with Teflon scrapers driven at 80 rpm, 5 HP motor, high-speed disperser with 6" blade with 7.5 HP motor, high-shear mixer with 5 HP motor, bushingless large square-hole stator with SLIM modification, one 1.5" tri-clamp port with ball valve, hose and wand, and funnel, mechanical seals with carbon vs. silicon carbide faces and Chemraz O-rings, vacuum cover with two 3" tri-clamp sight/charge ports with Metaglass teflon enclosed silicone gaskets, one RTD thermocouple mounted on a 1.5" tri-clamp port, port light, two 1.5" tri-clamp ports, two 2.5" tri-clamp ports with spray nozzles, one 1" tri-clamp port, mix can with 80-grit interior and exterior finish, 2" tri-clamp ball valve mounted off-center, 50psig stainless steel T304 jacket on side and bottom, casters and clamps, NEMA 12 control panel, 3-phase, 60 Hz, 208�230 V. | 2 WEEKS |
| RECON | VMC-40 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 117260 | Air/oil hydraulic lift, stainless steel T316 construction, 80-grit interior and exterior finish, PTFE and Teflon-enclosed silicone seals with Chemraz elastomers, explosion-proof design, vacuum capability, anchor agitator with 3-wing design and Teflon scrapers driven at 80rpm by a 5 HP motor, high-speed disperser with 6" blade operating at 2,550rpm driven by a 7.5 HP motor, high-shear mixer operating at 3,600rpm with 5 HP motor, bushingless large square-hole stator with SLIM modification, 1.5" tri-clamp port with ball valve, hose and wand, and funnel, mechanical seals with carbon vs. silicon carbide faces and Chemraz O-rings, vacuum cover with two (2) 3" tri-clamp sight/charge ports with Metaglass TES gaskets, one (1) RTD thermocouple mounted on a 1.5" tri-clamp port, port light, two (2) 1.5" tri-clamp ports, two (2) 2.5" tri-clamp ports with spray nozzles, one (1) 1" tri-clamp port, mix can with 80-grit interior and exterior finish, 2" tri-clamp ball valve mounted off-center, 50psig stainless steel T304 jacket on side and bottom, casters and clamps, NEMA 12 control panel, 3-phase, 60 Hz, 208�230 V. | 2 WEEKS |
| RECON | PVM-300 Versa Mix Multi Shaft Mixer Anchor Agitator Change Can Batch Homogenizer | 73801 | Air/oil hydraulic lift, T304, vacuum, 80-grit interior, explosion proof motors, Viton elastomers, cover includes one 2" NPT vacuum port, three tri-clamp ports with clean-in-place spray nozzles, one 6" sight/charge port, one 3" sight/charge port, can is T304 interior with 80-grit finish, 2" NPT ball valve, 15 psig carbon steel baffled jacket, fork lift channels, no casters (extra can available), SS304 three-wing anchor with scrapers driven by 15 HP motor, disperser driven by 25 HP motor, special Premax rotor-stator driven by 50 HP motor, all explosion proof, 3-phase, 60 Hz, 460 V. Electrical includes three explosion proof operator stations with on/off and speed controls, approximate weight 9,500 lbs. | 10 WEEKS |
| NEW | CDA-50 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer | 219410 | Air/oil hydraulic lift, vacuum, T316, 150-grit interior, 80-grit exterior, Viton seals, explosion proof motors, two-wing anchor (5 HP motor, 8�75 rpm), 7" disperser (10 HP motor, 260�2,620 rpm), vacuum cover includes two 3" Pyrex sight ports, one 6" tri-clamp port with cap, one 1" NPT port, flexi-lip seal with Kalrez, can is T316 with 150-grit interior and 80-grit exterior, painted carbon steel 50 psig jacket, 2" ball valve, casters, clamps, handle. | 1 WEEK |
| NEW | CDA-100 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer | Stainless steel T304, 80-grit finish, vacuum, change-can, air/oil hydraulic lift, stainless steel vacuum cover with one 1" FNPT port, two 3" sight/charge ports, 50 psig carbon steel jacket, 2" ball valve with 6" clearance, casters, flexi-lip seals, Viton, 8" disperser blade with 15 HP TEFC motor, two-wing anchor with 10 HP TEFC motor, 3-phase, 60 Hz, 230/460 V. Select required controls. Upgrade to T316 with 150-grit finish available. | 4-8 WEEKS | |
| NEW | CDA-200 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer | 218719 | Stainless steel T304, 80-grit finish, vacuum, change-can, air/oil hydraulic lift, stainless steel vacuum cover with one 1" NPT port, two 3" sight/charge ports, 50 psig carbon steel jacket, 2" ball valve with 6" clearance, casters, 80-grit interior, flexi-lip seals, Viton, 12" disperser blade with 20 HP TEFC motor, two-wing anchor with 10 HP TEFC motor, 3-phase, 60 Hz, 230/460 V. | 2 WEEKS |
| NEW | CDA-50 Dual Shaft Mixer Anchor Agitator Batch Change Can Paint Mixer | 219510 | Air/oil hydraulic lift, vacuum, T316 wetted parts with 150-grit interior finish, and 80-grit exterior, Viton, explosion proof limit switches.5HP explosion proof two-wing anchor, triangular cross section, hinged scrapers. 10HP explosion proof disperser, 7" blade. T316 vacuum cover, two 3" (Cherry Burrell) sight/charge ports, one 1" FNPT, viton cover O-ring, flexi lip with kalrez O-ring on agitators. Mix can with T316 150-grit interior, vacuum, 50psig painted carbon jacket on side/bottom, 2" FNPT ball valve, casters, clamps. NEMA 4X VFD's, 3-phase, 60Hz, 230V, shipped loose. | 10 WEEKS |
| NEW | Tank, 40-GAL Mix Vessel | 40-gallon vessel, T304, atmospheric design, flat bottom, open top, casters, two Type 304 handles, dimensions 34" ID x 12-3/16" deep x 19-7/8" overall height, removable strainer with two handles, no outlet. | STOCK | |
| RECON | TANK, 200-GAL Pressure Vessel Storage Tank | 200-gallon working capacity, 250-gallon full mixing vessel, T316L, 240-grit interior, 180-grit exterior, 40" OD x 40.25" straight side rated for 13 psig internal pressure at 212�F, removable dished cover with clamps, ASME 100 psig at 350�F jacket on sides only, insulated with 2" side and bottom sheathed in stainless steel T304 welded, 2" MCF ball valve with actuator bottom center at 5.75" off floor, legs designed for addition of load cells, two thermowells bottom and sidewall, 18" manway, two 1-1/2" tri-clamp ports with Gama Jet VI spray machines 25 gpm at 45 psig 360-degree coverage, 3" tri-clamp with explosion proof fiber optic light, 3" tri-clamp sight glass port, 2" tri-clamp, four 1" tri-clamp ports, lifting lugs. | STOCK | |
| NEW | Tank, 500-GAL Mix Vessel | 500-gallon working volume mix vessel, 590-gallon full holding, T304, atmospheric design, drive support with open top, flanged and dished bottom, three T304 support legs with 6-1/2" square x 1/2" thick mounting pads, two T304 lift lugs, 48" ID x 72" straight side wall x 8" deep dished bottom, rolled angle upper rim 2" wide, one 3" 150# ANSI flange outlet center bottom located at 29-1/2" off floor, mill finish, internal welds ground smooth, overall height 117" | STOCK | |
| NEW | DS-10 Discharge System Press | 117636 | Standard SS304, 80-grit finish, 25 psig under the platen, Viton O-ring, 1 HP explosion proof motor, manual directional control valve. | STOCK |
| NEW | DS-40 Discharge System Press | 117501 | Standard SS304, 80-grit finish, 50 psig under the platen, Viton O-ring, 1 HP TEFC motor, manual directional control valve, one 3" tri-clamp port with flush plug, one 1" FNPT port, NEMA 12 motor starter with on/off, 3-phase, 60 Hz, 230 V, mounted and wired, special platen design with larger cross-section O-ring for non-machined discharge-rated mix cans. | STOCK |
| NEW | DS-40 Discharge System Press | Standard, SS304 80-grit finish, 25-psig under the platen, Viton O-ring, 1HP explosion proof motor, manual directional control valve. | TBD | |
| RECON | DS-1QT-SS Discharge System Press | 72571 | 110 psig under platen, extended height, all stainless steel construction, bench and discharge system bridge sheathed in SS304, Viton O-ring, 1/2 HP TEFC motor, 1-phase, 60 Hz, 115 V, NEMA 4X on/off starter with raise/lower selector switch and E-stop, foot pedal controls, stainless steel bench with leveling pads, pressure chart. | STOCK |
| RECON | CDS-2 Discharge System Press | 58778 | Old "C" frame design with double O-rings, 65 psig under the platen, 1" MNPT vent on platen with plug, SS304, 80-grit finish, Viton O-ring, XP 3ph, 60Hz, 230V motor. NEMA 12 on/off starter, 1/2hp 3/60/230V. Cast base with cut out for ball valve. CAN NOT BE USED WITH CASTERS ON MIX CAN. No bench. | 3-4 WEEKS |
| RECON | DS-4 Discharge System Press | 217642 | SS304, 80-grit finish, Viton O-ring, 30 psig under platen, 3ph, 60Hz, 230V 1/2 HP TEFC motor, for use with 4-gallon mix cans, bench with leveling pads, NEMA 12 on/off operator station, manual directional control. | 2-3 WEEKS |
| RECON | DS-5 Discharge System Press | 116103 | SS316, 240-grit finish, EPDM O-ring, 30 psig under the platen, 3ph, 50Hz, 400V 1/2HP explosion-proof ATEX motor. NEMA 4X operator station suited for Zone 21/Class II Div 1 (Shipped loose). SS304 bench on casters, alignment pins, brush finish. Vacuum pump mounted on lower shelf. CE-certified. | 3 WEEKS |
| RECON | DS-5 Discharge System Press | 116104 | SS316, 240-grit finish, EPDM O-ring, 30 psig under the platen, 3ph, 50Hz, 400V 1/2HP explosion-proof ATEX motor. NEMA 4X operator station suited for Zone 21/Class II Div 1 (Shipped loose). SS304 bench on casters, alignment pins, brush finish. Vacuum pump mounted on lower shelf. CE-certified. | 3 WEEKS |
| UNUSED | DS-5 Discharge System Press | 117901 | SS16, 150-grit finish, Viton O-ring, 3ph, 60Hz, 230V 1/2 HP explosion proof motor, 30 psig under platen, NEMA 7/9 on/off operator station, carbon steel bench with SS304 80-grit top. | STOCK |
| RECON | DS-40 | 104303 | Painted carbon steel structure, SS304, 80-grit wetted parts, Viton O-ring, 25 psig under platen, 3ph, 60Hz, 230/460V explosion-proof motor, NEMA 7/9 operator start/stop station, 3ph, 60Hz, 460V. | 3-4 WEEKS |
| RECON | HED-100 Discharge System Press | 112507 | Elevated DS-100, 3ph, 60Hz, 460V 5HP TEFC motor, 50 psig under platen, Viton O-ring, SS304, NPT vent with plug, 36" discharge height, dual cylinders for lifting, single cylinder for discharging, pneumatic lift lock with limit switch, NEMA 7/9 explosion proof control panel, power unit supplied for remote installation. | STOCK 1-WEEK |
| NEW | TRM 2.5 X 5 Three Roll Mill | 2.5" x 5" three-roll mill, 1/2 HP explosion proof motor, bench/tabletop model, explosion proof safety trip switch, stainless steel 440C precision ground rolls cored for water cooling and heating, adjustable stainless steel apron, Teflon end plates, nip block, NEMA 12 control panel mounted and wired. | 6-8 WEEKS | |
| NEW | TRM 4 X 8 Three Roll Mill | Floor model with TEFC motor, stainless steel 440C rolls, Teflon end plates, NEMA 12 control panel mounted and wired. | 6-8 WEEKS | |
| NEW | TRM 5 X 12 Three Roll Mill | TEFC motor, stainless steel 440C rolls, Teflon end plates, NEMA 12 control panel mounted and wired.. | 3-4 WEEKS | |
| NEW | TRM 5 X 12 Three Roll Mill | TEFC motor, carbon steel 52100 rolls, Teflon end plates, NEMA 12 control panel mounted and wired. | 3-4 WEEKS | |
| RECON | TRM 4 X 8 Three Roll Mill | 218038 | 4" x 8" bench model, 1 HP explosion proof motor, explosion proof trip safety switches, nip block, carbon steel 52100 hardened precision ground rolls, rotary pressure joints with cooling manifold, valves and collection trough, stainless steel T304 apron and adjustable Teflon end plates, NEMA 7/9 control panel, VFD keypad, start/stop, speed potentiometer, forward/reverse, clean mode on/off, E-stop, emergency brake, 3-phase, 60 Hz, 230 V, mounted and wired. | STOCK |
| NEW | KE-VIU20 Kneader Extruder | 115537 | ROSS/AMK KE VIU20 C12839, 23-liter working capacity, vacuum-rated kneader extruder, Class IV, 5 HP TEFC kneading blade motor, 3 HP TEFC extrusion screw, stainless steel T316L wetted parts, stainless steel T304 heating and cooling jacket rated for 3 bar with temperature probe, 240-grit interior, 150-grit exterior, mounted on stainless steel plate with casters for portability, controls 460 V, NEMA 4X ROSS Syscon operator control system shipped loose. | STOCK |
| NEW | 42S-1 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3/4 HP TEFC motor, T316, sanitary design, atmospheric, center discharge 36" off floor with legs, all stainless steel polished to 80-grit finish, Teflon braided square packing, 80-grit finish, one-piece cover, 230/460 volt, 3-phase, 60 Hz, high horsepower capable, 2" dust-tight knife gate valve, note: maximum 85 rpm. | 8-10 WEEKS | |
| NEW | 42N-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3 HP TEFC motor, stainless steel T304, atmospheric, center discharge 36" off floor on legs, single cover with safety limit switch, Teflon braided square packing, stainless steel split stuffing boxes, one-piece cover, silicone cover gasket, shaft guards, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 volt, 3-phase, 60 Hz, 3" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-5S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, single cover with safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, 3" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3 HP TEFC, stainless steel T316, new sanitary design, atmospheric, all stainless steel polished to 150-grit interior finish, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, one-piece cover, silicone cover gasket, shaft guards, 150-grit interior finish, 230/460 V, 3-phase, 60 Hz, 3" dust-tight knife gate valve with manual handwheel. | 8-10 WEEKS | |
| NEW | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3 HP TEFC, stainless steel T316, new sanitary design, atmospheric, all stainless steel polished to 150-grit interior finish, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, one-piece cover, silicone cover gasket, shaft guards, 150-grit interior finish, 230/460 V, 3-phase, 60 Hz, 3" dust-tight knife gate valve with manual handwheel. | 8-10 WEEKS | |
| NEW | 42S-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 3 HP TEFC motor, stainless steel T316, new sanitary design, atmospheric, all stainless steel polished to 80-grit finish, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, one-piece cover, silicone cover gasket, shaft guards, 230/460V, 3-phase, 60 Hz, 3" dust-tight knife gate valve with manual handwheel. | 8-10 WEEKS | |
| NEW | 42N-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 5 HP TEFC, stainless steel T304, atmospheric, center discharge 36" off floor, Teflon braided square packing, stainless steel split stuffing boxes, two-piece cover, silicone cover gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, 4" dust-tight knife gate valve with manual handwheel. | 8-10 WEEKS | |
| NEW | 42N-10S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 5 HP TEFC motor, stainless steel T316, new sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, two-piece cover, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz. | 8-10 WEEKS | |
| NEW | 42N-10SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 5 HP TEFC motor, stainless steel T316, new sanitary design, atmospheric, all stainless steel, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, two-piece cover, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, 230/460V, 3-phase, 60 Hz, high horsepower capable, 4" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-18 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 7.5 HP TEFC motor, stainless steel T304, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel split stuffing boxes, silicone cover gasket, shaft guards, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, high horsepower capable, 4" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-18S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 7.5 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, high horsepower capable, 4" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-18SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 7.5 HP TEFC motor, stainless steel T316, sanitary design, all stainless steel, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, shaft guards, all stainless steel polished to 150-grit interior finish, 230/460V, 3-phase, 60 Hz, high horsepower capable. | 8-10 WEEKS | |
| NEW | 42N-25S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 10 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, 4" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-25SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 10 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, all stainless steel, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, 230/460V, 3-phase, 60 Hz. | 8-10 WEEKS | |
| NEW | 42N-36 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 15 HP TEFC motor, stainless steel T304, atmospheric, center discharge 36" off floor, Teflon braided square packing, stainless steel split stuffing boxes, silicone cover gasket, all stainless steel 60-grit finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, high horsepower capable, 6" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-36S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 15 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards, stainless steel 150-grit interior finish, painted carbon steel support, 230/460V, 3-phase, 60 Hz, 6" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-36SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 15 HP TEFC motor, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, silicone cover gasket, shaft guards. | 8-10 WEEKS | |
| NEW | 42N-52 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 20 HP TEFC motor, stainless steel T304, atmospheric, center discharge 36" clearance off floor, stainless steel split stuffing boxes, silicone cover gasket, all stainless steel 60-grit finish, 230/460V, 3-phase, 60 Hz, 8" dust-tight knife gate valve. | 8-10 WEEKS | |
| NEW | 42N-52S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 20 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, neoprene cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, high horsepower capable. | 8-10 WEEKS | |
| NEW | 42N-52S Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 20 HP TEFC motor, stainless steel T316, sanitary design, atmospheric, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, neoprene cover gasket, shaft guards, all stainless steel polished to 150-grit interior finish, painted carbon steel supports, 230/460V, 3-phase, 60 Hz, high horsepower capable. | 8-10 WEEKS | |
| NEW | 42B-1 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 1/2 HP TEFC motor, stainless steel T304, atmospheric, 99 rpm, center discharge 36" off floor, Teflon braided square packing, one-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 2" knife gate valve. | 3 WEEKS | |
| NEW | 42B-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 1/2 HP TEFC motor, stainless steel T304, atmospheric, 70 rpm, center discharge 36" off floor, Teflon braided square packing, one-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 3" knife gate valve. | 3 WEEKS | |
| NEW | 42B-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 3 HP TEFC motor, stainless steel T304, atmospheric, 56 rpm, center discharge 36" off floor, Teflon braided square packing, two-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 4" knife gate valve. | 3 WEEKS | |
| NEW | 42B-18 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 5 HP TEFC motor, vertically mounted motor, stainless steel T304, atmospheric, 45 rpm, center discharge 36" off floor, Teflon braided square packing, two-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 4" knife gate valve. | 3 WEEKS | |
| NEW | 42B-25 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 7.5 HP TEFC motor, stainless steel T304, atmospheric, 43 rpm, center discharge 36" off floor, Teflon braided square packing, two-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 4" knife gate valve. | 3 WEEKS | |
| NEW | 42B-36 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | �B Design� one 10 HP TEFC motor, stainless steel T304, atmospheric, 40 rpm, center discharge 36" off floor, Teflon braided square packing, two-piece cover with silicone gasket, all stainless steel polished to 60-grit finish, painted carbon steel supports, 230/460 V, 3-phase, 60 Hz, rated at 35 pounds per cu.ft., 6" knife gate valve. | 3 WEEKS | |
| RECON | 42N-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 117942 | 3 HP TEFC motor, stainless steel T304, 80-grit finish, atmospheric, center discharge, 42" valve to floor, casters, 3" knife gate valve, single cover, Teflon braided packing, silicone door gasket, bolted ribbon, NEMA 12 limit switch, VFD 3 HP, NEMA 4X, 1-phase, 60 Hz, 230 V input, 3-phase, 60 Hz, 230 V output, mounted and wired. | 2 WEEKS |
| RECON | 42N-5 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 215857 | 3 HP explosion proof motor, stainless steel T304, 60-grit finish, atmospheric, center discharge 36" off floor on legs, 8" liquid-tight knife gate valve with 8" ANSI flange, single cover with explosion proof safety limit switch, three 1/2" MNPT ports, one-piece perforated safety grate with 1/2" holes, Teflon braided square packing, stainless steel T304 split stuffing boxes, silicone gasket, shaft guards, carbon steel painted, two thermowells explosion proof, spray bar with four 90-degree fan-type nozzles, 5 HP explosion proof chopper side/back/center mounted, NEMA 12 VFDs for 3 HP and 5 HP motors, 3-phase, 60 Hz, 230 V. | 1-2 WEEKS |
| RECON | 42N-5SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 116562 | 5HP washdown motor, SS316 wetted parts, sanitary design, atmospheric, center discharge 36" off floor on legs, electronically actuated liquid tight 2" flush mount ball balve with Teflon, PEEK and silicone seats/O-rings. Two-piece SS304 covers with two 4" tri-clamp ports. Cover-to-trough clamps. Teflon braided square packing, SS304 split stuffing boxes. Ribbon with welded stub shafts. All SS exterior. 150 grit interior finish / 80-grit exterior finish. 100-PSIG jacket for heating/cooling and insulation. Type J thermo in sidewall. NEMA 4X control panel, mounted and wired. 10 step, 10 recipe system. 3/60/208V. Temperature Control Unit. | 2 WEEKS |
| NEW | 42N-1SS Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 219317 | 3/4 HP TEFC motor, stainless steel T316, new sanitary design, atmospheric, all stainless steel, center discharge 36" off floor on legs, safety limit switch, Teflon braided square packing, stainless steel T316 split stuffing boxes, two-piece cover, silicone cover gasket, shaft guards, all stainless steel 150-grit finish, carbon steel painted, 230/460 V, 3-phase, 60 Hz, high horsepower capable, 2" dust-tight knife gate valve, controls include VFD 1 HP, NEMA 4X, 3-phase, 50/60 Hz, 200/240 V. | STOCK |
| RECON | 42N-10 Ribbon Blender Dry Blender Horizontal Mixer Dryer Plow Blender Powder Blender | 116761 | 5 HP TEFC motor, 3-phase, 60 Hz, 208 V, T304 wetted parts, 80-grit interior, NEMA 12 limit switches, bolted ribbon, center discharge, atmospheric, silicone cover gasket, Teflon braided packing, top speed approximately 56 rpm at 60 Hz, 4" dust-tight knife gate valve, carbon steel painted support legs, 36" valve to floor, NEMA 4X VFD, 5 HP, 3-phase, 60 Hz, 208 V, start/stop, speed control with forward/reverse switch. | 3-4 WEEKS |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender | 118484 | 1 cu.ft. V-cone blender, 2 HP TEFC motor, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 36 rpm, painted steel support, 4" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 4-6 WEEKS |
| NEW | VCB-1 V Cone Blender Tumble Blender Dry Powder Blender | 118486 | 1 cu.ft. V-cone blender, 2 HP TEFC motor, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 36 rpm, 2 HP intensifier bar with spray bar and spray nozzles, painted steel support, 4" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 4-6 WEEKS |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender | 114851 | 5 cu.ft. V-cone blender, 5 HP TEFC, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 24 rpm, painted steel support, 6" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 2-WEEKS |
| NEW | VCB-5 V Cone Blender Tumble Blender Dry Powder Blender | 114867 | 5 cu.ft. V-cone blender, 5 HP TEFC motor, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 24 rpm, 3 HP intensifier bar, painted steel support, 6" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 2-4 WEEKS |
| NEW | VCB-10 V Cone Blender Tumble Blender Dry Powder Blender | 118481 | 10 cu.ft. V-cone blender, 10 HP TEFC motor, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 20 rpm, painted steel support, 8" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 4-6 WEEKS |
| NEW | VCB-10 V Cone Blender Tumble Blender Dry Powder Blender | 118482 | 10 cu.ft. V-cone blender, 10 HP TEFC motor, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, 20 rpm, 7.5 HP intensifier bar with spray bar and spray nozzles, painted steel support, 8" butterfly valve, 24" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 150 pounds per cu.ft. | 4-6 WEEKS |
| RECON | VCB-7.5 V Cone Blender Tumble Blender Dry Powder Blender | 115311 | 7.5 cu.ft. V-cone blender, 5 HP TEFC motor, atmospheric, stainless steel T316, 80-grit interior finish, mill finish exterior, 20 rpm, 5 HP intensifier bar, painted steel support, 8" butterfly valve, 36" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230 V, NEMA 12 control panel loose, rated at 150 pounds per cu.ft. | 4-WEEKS |
| RECON | DCB-10 V Cone Blender Tumble Blender Dry Powder Blender | 114384 | 10 cu.ft. (283.2 liter) double-cone blender, 7.5 HP explosion proof motor, atmospheric, stainless steel T304, 150-grit interior finish, 80-grit exterior finish, 20 rpm, intensifier bar and spray bar with 5 HP explosion proof motor drive and magnetic seals, painted steel support, 8" butterfly valve, 36" clearance under valve, mechanical safety railing with limit switch, 3-phase, 60 Hz, 230 V, NEMA 12 control panel with touchscreen, E-stop, disconnect, NEMA 7/9 explosion proof operator panel with start/stop, potentiometer, jog, E-stop, rated at 125 pounds per cu.ft. | 2-4 WEEKS |
| RECON | VCB-5 | 109415 | 5 cu.ft (140 liter) V-cone tumble blender, T316, 5 HP TEFC motor operating at 3�22 rpm, atmospheric, stainless steel T316, 240-grit mirror interior finish, 150-grit exterior finish, stainless steel T304 support with 150-grit finish, 6" butterfly valve with silicone seat, 24" clearance under valve, safety railing with limit switch, 3-phase, 60 Hz, 230/460 V, rated at 125 pounds per cu.ft. | 1-2 WEEKS |
| RECON | VCB-5 | 114866 | 5 cu.ft. (140 liter) V-cone tumble blender, T316, 5 HP TEFC brake motor operating at 3�24 rpm, 3 HP intensifier bar, atmospheric, stainless steel T316, 150-grit interior finish, 80-grit exterior finish, carbon steel painted support, 6" tri-clamp butterfly valve with silicone seat, 24" clearance under valve, safety railing with limit switch, 3-phase, 60 Hz, 460 V, 3 HP and 5 HP VFDs mounted to blender, rated at 125 pounds per cu.ft. | 4-6 WEEKS |
| RECON | TE.3-50 Turboemulsifier Counter Rotating Mixer | 67556 | Sanitary specifications include vacuum pump, heater/chiller, self-contained system, raise/lower function, vacuum pump on/off, two inverters, other controls not included, call for specifications. | 2-4 WEEKS |
| NEW | HSM-100LSK-I Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab | High shear mixer model HSM-100LSK-I with VFD design, 3/4 HP, single-phase, 60 Hz, 115 V, 20 amps, speed range 500�10,000 rpm, available options include high speed disperser, micro mixer, in-line mixer, quad configuration, double-taper propeller, various stators, bushings, high speed disperser blades, propellers, beaker clamp, and vessels. | 1-2 DAYS | |
| NEW | HSM-100LCIT Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer Benchtop Lab | Stainless steel T316 wetted parts, 1 HP drive, 115 V, single-phase, 50/60 Hz, 20 amps, option for 190 V or 230 V, variable speed 500�10,000 rpm with speed calibration to �1%, constant torque, touchscreen control with start/stop, speed, time, digital display for speed, temperature display 0�300�F or 0�150�C, RTD temperature probe optional, batch timer display, percent of load display, calibration screens for temperature and speed, raise/lower lift push-buttons, calibration, timer, and other function controls, stainless steel T316 mixer/emulsifier assembly with disintegrating, slotted, and fine screen heads, Teflon bushing, options include disperser, micro mixer, in-line mixer, quad configuration, temperature probe, and beaker clamp. | STOCK | |
| NEW | HSM100LH-1 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 1 HP high shear rotor/stator mixer, air/oil hydraulic lift, table or bench mount design, 1-3/8" diameter mixer/emulsifier operating at 10,000 rpm, slotted head, Teflon bushing, stainless steel T304, shaft guard, limit switches, adjustable can lock, inverter duty 10:1 TEFC motor, options include other stators and bushings, VFD, bench, interchangeable disperser and in-line assemblies, in-line can be used with quad configuration and double mechanical seals with barrier tank. | 1 WEEK | |
| NEW | HSM100LH-2 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 2 HP high shear rotor/stator mixer, air/oil hydraulic lift, table or bench mount design, 2" diameter mixer/emulsifier operating at 6,900 rpm, slotted head, Teflon bushing, stainless steel 304, shaft guard, limit switches, adjustable can lock, inverter duty 10:1 TEFC motor, options include other stators and bushings, VFD, bench, interchangeable disperser and in-line assemblies, in-line can be used with quad configuration and double mechanical seals with barrier tank. | 1 WEEK | |
| NEW | HSM100LH-2 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 2 HP high shear rotor/stator mixer, air/oil hydraulic lift, table or bench mount design, disperser assembly with 3" blade operating at 6,900 rpm, shaft guard, explosion proof limit switches, adjustable can lock, inverter duty 10:1 TEFC motor. | 1 WEEK | |
| NEW | HSM-101 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | T316 wetted parts, explosion proof motor, 50/60 Hz, slotted head, Teflon bushing. | STOCK | |
| NEW | HSM-105 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | T316 wetted parts, explosion proof motor, 50/60 Hz, slotted head, Teflon bushing. | STOCK | |
| NEW | HSM-110 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | T316 wetted parts, explosion proof motor, 50/60 Hz, slotted head, Teflon bushing. | STOCK | |
| NEW | HSM400DLA Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 1 HP TEFC motor, 3ph, 60Hz, 230/460V VFD-capable motor, single mechanical seal, Viton seals, stainless steel T316 with 80-grit finish, slotted head, carbon steel painted base. | 1-2 WEEKS | |
| NEW | HSM400DLA Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | Enclosed design with carbon steel painted base, riser and bench, 1 HP TEFC VFD-rated motor, 3-phase, 60 Hz, 230/460 V, 10,000 rpm, double mechanical seal with Kalrez rated for 250 psig with barrier tank, Viton O-rings, slotted, fine screen, and disintegrating stators, NPT inlet and outlet, 1 HP NEMA 12 VFD, 3-phase, 60 Hz, 230 V, leveling pads, mix chamber pressure gauge, inlet and outlet valves. | 1-2 WEEKS | |
| NEW | HSM-401/3 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 3 HP standard specifications, slotted head, single mechanical seal, Viton, single seal. | STOCK | |
| NEW | HSM-405 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 5 HP standard specifications, slotted head, single mechanical seal, Viton, single seal. | STOCK | |
| NEW | HSM-410 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 10 HP standard specifications, slotted head, single mechanical seal, Viton, single seal. | STOCK | |
| NEW | HSM-450 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 118552 | 50 HP explosion proof motor 230/460V, 60Hz, 3ph, slotted head, double mechanical seal with silicon carbide faces and barrier system including tank, Viton seals. | STOCK |
| NEW | HSM-100LCI-T Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 219782 | TOUCH SCREEN CONTROL, 1HP Drive, 1/60/115v, 500-10,000rpm +/-1% w/calibration. Speed, Load, Temp, Timer displays, 15" lift, 16" under blade R/L push buttons. HSM | STOCK |
| NEW | HSM-100LH-2 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 219515 | Bench-top design, air/oil hydraulic lift, 2 HP explosion proof motor, T316 wetted parts, explosion proof limit switches, high shear mixer assembly with square-hole stators and Teflon bushing, operating at 720�7,200 rpm for use in 3�5 gallon vessels, SLIM system with modified lower flange, ball valve, hose, and stainless steel wand with all 3/4" tri-clamp connections, bench constructed of painted carbon steel with lower shelf and leveling mounts, controls include NEMA 4X 2 HP VFD, 3-phase, 60 Hz, 230 V, shipped loose. | 4 WEEKS |
| RECON | HSM-110 Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 114650 | Stainless steel T316 wetted parts, 10 HP stainless steel washdown motor, 3-phase, 60 Hz, 230/460 V, slotted stator, Teflon bushing, controls include NEMA 4X stainless steel enclosure with NEMA 3R fan shrouds, 10 HP VFD, 3-phase, 60 Hz, 460 V, motor fuse protection, filter and fan cooling package, 4" color touchscreen displaying speed, load, and cycle timer, E-stop, mounted and wired using seal-tite. | 1-WEEK |
| NEW | HSM-125 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer | 118662 | T316 wetted parts, 25 HP explosion proof motor, 60 Hz, slotted stator, Teflon bushing, shaft length 50.5" from bottom mounting flange to bottom of stator | STOCK |
| RECON | HSM-410 Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer | 218166 | Explosion proof motor, 10 HP, double mechanical seal rated for 130 psig with barrier tank, slotted head with Stellite-tipped rotor, 2" FNPT outlet, 2-1/2" female FNPT inlet, stainless steel T316, Viton seals. | 1 WEEK |
| RECON | HSM-410S Inline High Shear Mixer Rotor stator Mixer Emulsifier Eductor Pump Homogenizer | 60667 | Explosion proof motor, 10 HP, washdown design, double mechanical seal with barrier tank, slotted head, 2" tri-clamp outlet, 2-1/2" tri-clamp inlet, stainless steel T316, 150-grit finish, Viton seals, Voss clamps on mix chamber, includes 10 HP VFD, 230 V. | 2-WEEKS |
| RECON | HSM-510 Vacuum Batch High Shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 200224 | 10 HP, slotted head, bronze bushing, single mechanical seal for vacuum application. | 2-3 WEEKS |
| RECON | HSM-703XC-20 Ultra High Shear Mixer Inline Mixer Rotor Stator Mixer Emulsifier Homogenizer X Series Quad Slot Mega Shear Colloid Mill | 204329 | TEFC motor, 20 HP, 3" diameter Mega-Shear rotor/stator, X-5 and quad rotor/stators, 150 psig mix chamber, standard machine finish, NPT inlet and outlet, double cartridge mechanical seal, Viton seals, NEMA 1 VFD, 20 HP, 3-phase, 60 Hz, 460 V, mounted and wired, non-standard belt design and speed, 14,400 rpm at 75 Hz. | STOCK |
| NEW | HSM-400SC-5 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM | Modified HSM-400 lab-size design, sanitary horizontal configuration, 5 HP TEFC motor, double mechanical seal with barrier tank, Viton seals, stainless steel T316, 80-grit finish, 1" tri-clamp inlet and outlet with in-line slim system including hose and wand, one-piece inlet/stator slotted head, carbon steel flat base and tube riser with leveling pads, NEMA 1 VFD, 3-phase, 60 Hz, 230 V, mounted and wired, carbon steel painted drive base, flat base, and tube riser, no drive enclosure. | 2-3 WEEKS | |
| NEW | HSM-405SC-25 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM | 117904 | Modified HSM-405 design, sanitary horizontal configuration, 25 HP explosion proof motor, Viton mix chamber O-rings, double mechanical seal with barrier tank and liquid level switch, stainless steel T316, 150-grit finish, wing nuts, one 2" tri-clamp inlet and one 2" tri-clamp outlet with in-line slim system including 1-1/2" slim port, hose and wand, hopper with integrated bench top, one-piece inlet/stator large square head, stainless steel 2 cuft. hopper for powder loading, stainless steel portable cart with casters, NEMA 4X VFD, 3-phase, 60 Hz, 460 V, shipped loose, explosion proof operator station with start/stop, speed, E-stop, mounted, NEMA 12 DC power supply and barrier for level switch, 230 V. | 1-2 WEEKS |
| NEW | HSM-405SC-25 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM | Modified HSM-405 design, sanitary horizontal configuration, 25 HP explosion proof motor, Viton mix chamber O-rings, double mechanical seal with barrier tank and Kalrez O-rings, stainless steel T316, 150-grit finish, wing nuts, one 2" tri-clamp inlet and one 2" tri-clamp outlet with in-line SLIM system including 1-1/2" SLIM port, hopper, one-piece inlet/stator large square head, stainless steel 2 cuft. hopper for powder loading, stainless steel portable cart with casters. | 6-8 WEEKS | |
| RECON | HSM-430SC Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM | 216127 | In-line SLIM sanitary horizontal mixer, 30 HP explosion-proof motor operating at 1,800 RPM (direct drive), double mechanical seal with barrier tank and Viton elastomers, stainless steel 316 construction with 150-grit finish, 3" tri-clamp inlet and outlet, in-line SLIM (I-SLIM) 2.5" tri-clamp port with 2 cu. ft. hopper, one-piece inlet/stator large square head, stainless steel hopper assembly for powder loading, stainless steel portable cart with casters, NEMA 4X panel with 30 HP VFD, 3-phase, 60 Hz, 460 V, mounted and wired. | 1-WEEK |
| RECON | HSM-412SB-150 Inline High Shear Mixer Rotor Stator Mixer Emulsifier Eductor Pump Homogenizer SLIM | 67295 | Modified ME-450XS, 150 HP TEFC motor, double mechanical seal and barrier tank, 9" rotor and stator, Viton seals, stainless steel T316, 150-grit finish, Voss tri-clamp connections, 2" tri-clamp inlet and 3" tri-clamp outlet with in-line SLIM system, 3" tri-clamp and 3" ball valve, hose and wand, slotted head. | 2-4 WEEKS |
| NEW | HSM100LH-1 Batch High shear Mixer Rotor Stator Mixer Emulsifier Homogenizer | 1 HP high speed disperser, air/oil hydraulic lift, table or bench mount design, 2" disperser blade operating at 10,000 rpm, stainless steel T304, shaft guard, limit switches, adjustable can lock, inverter-duty 10:1 TEFC motor, options include VFD, bench, interchangeable rotor/stator attachments available (batch and inline) | 1 WEEK | |
| NEW | HSM100LH-2 High Speed Disperser Batch | 2 HP high speed disperser, air/oil hydraulic lift, table or bench mount design, 2" disperser blade operating at 10,000 rpm, stainless steel T304, shaft guard, limit switches, adjustable can lock, inverter-duty 10:1 TEFC motor, options include VFD, bench, interchangeable rotor/stator attachments available (batch and inline) | 1 WEEK | |
| NEW | HSD-5 High Speed Disperser Batch | 5 HP high-speed disperser, lift mounted on floor with 48" rise, 6" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-7.5 High Speed Disperser Batch | 7.5 HP high-speed disperser, lift mounted on floor with 48" rise, 8" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-10 High Speed Disperser Batch | 10 HP high-speed disperser, lift mounted on floor with 48" rise, 10" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-15 High Speed Disperser Batch | 15 HP high-speed disperser, lift mounted on floor with 48" rise, 12" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-20 High Speed Disperser Batch | 20 HP high-speed disperser, lift mounted on floor with 48" rise, 14" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-25 High Speed Disperser Batch | 25 HP high-speed disperser, lift mounted on floor with 54" rise, 16" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| NEW | HSD-30 High Speed Disperser Batch | 30 HP high-speed disperser, lift mounted on floor with 54" rise, 16" blade at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor. | 1-2 WEEKS | |
| RECON | HSD-5-VAC High Speed Disperser Batch | 106702 | 5 HP explosion proof high-speed disperser, air/oil hydraulic lift mounted on floor with 30" rise, 5" blade operating at 3,740 rpm at 3.5" off inside bottom of mix vessel, adjustable blades, stainless steel T304, Viton seals, explosion proof limit switches, can lock, vacuum cover with two 2" sanitary and gasketed ports, one 1/2" NPT port, vessel-to-cover clamps, mix vessel vacuum-rated, 15-gallon working capacity, 20-gallon full holding, dished bottom, 50 psig at 150�F stainless steel jacket, thermowell, 80-grit finish interior and exterior, 2" ball valve NPT at 22.5" off floor, legs with casters, explosion proof operator station with start/stop, speed and load display, NEMA 1 VFD, 5 HP, 3-phase, 60 Hz, 230 V. | 3-4 WEEKS |
| RECON | HSD-15 High Speed Disperser Batch | 117262 | 15 HP high-speed disperser, lift mounted on floor with 48" rise, 12" blade at 8" off floor, stainless steel T304, shaft guard, explosion proof limit switches, adjustable can lock, explosion proof motor. | 1 - 2 WEEKS |
| RECON | HSD-30 High Speed Disperser Batch | 216865 | 30 HP high-speed disperser, lift mounted on floor with 54" rise, 16" blade operating at 115�1,150 rpm at 8" off floor, stainless steel T304, shaft guard, limit switches, adjustable can lock, TEFC motor, NEMA 4X VFD, 230 V. | 3 WEEKS |
| NEW | PBA-2 Mix Vessel | 2 HP TEFC motor, air/oil hydraulic lift, stainless steel T304, 80-grit finish, table mount design, mounted on bench, operating range 36�540 rpm (6�90 Hz), 6" three-wing bow-tie blade, other sizes and types available. | 3-4 WEEKS | |
| NEW | PBA-5TMD w/500-GAL Tank Mix Vessel | PBA-5TMD, 5 HP TEFC motor, 3-phase, 60 Hz, 230/460 V, anchor agitator with two wings operating at 33 rpm, tank mounted, direct drive with right-angle gear reducer, 500-gallon working volume mix vessel, 590-gallon full holding, T304, atmospheric design, drive support with open top, flanged and dished bottom, three Type 304 support legs with 6-1/2" square x 1/2" thick mounting pads, two T304 lift lugs, dimensions 48" ID x 72" straight side wall x 8" deep dished bottom, rolled angle upper rim 2" wide, one 3" 150# ANSI flange outlet center bottom located at 41-1/2" off floor, mill finish, internal welds ground smooth, overall height 131" | STOCK | |
| NEW | PBA-5TMD w/500-GAL Tank Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade | PBA-5TMD, 5 HP TEFC motor, 3-phase, 60 Hz, 230/460 V, anchor agitator with two wings operating at 33 rpm, tank mounted, direct drive with right-angle gear reducer, 500-gallon working volume mix vessel, 590-gallon full holding, T304, atmospheric design, drive support with open top, flanged and dished bottom, three Type 304 support legs with 6-1/2" square x 1/2" thick mounting pads, two T304 lift lugs, dimensions 48" ID x 72" straight side wall x 8" deep dished bottom, rolled angle upper rim 2" wide, one 3" 150# ANSI flange outlet center bottom located at 41-1/2" off floor, mill finish, internal welds ground smooth, overall height 131", | STOCK | |
| NEW | PBA-10 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade | 10 HP explosion proof motor, air/oil hydraulic lift, stainless steel T304, 80-grit finish, floor mount design, operating range 44�175 rpm, equipped with 18", 20", and 22" three-wing bow-tie blades, other sizes and types available. | 3-4 WEEKS | |
| RECON | PBA-1 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade | 111827 | 1 HP explosion proof motor, air/oil hydraulic lift, stainless steel T304, 80-grit finish, Viton seals, floor mount design, operating range 9�90 rpm, 7.5" diameter four-blade axial flow paddle blade pitched at 45 degrees located 24" off floor, vacuum and +2 psig cover with two 4" 150# flanges with blind caps, two 1" FNPT ports, one 6" sight and gasketed port with Metaglass, one 1" tri-clamp port, two 1" 150# flanges with blind caps, control panel NEMA 4X stainless steel explosion proof purged, 3-phase, 60 Hz, 460 V, 4" color display, stainless steel E-stop, timer, temperature display, 1 HP VFD mounted and wired, mix vessel T316, 80-grit finish, 36-gallon working capacity, 44-gallon full holding, 22" ID x 24" straight side, dished bottom, 30 psig at 350�F stainless steel jacket with 1" NPT ports, thermowell, 2" NPT ball valve, clamps, three legs with casters. | 2-4 WEEKS |
| RECON | PBA-2 Paddle Blade Agitator Gentle Agitator High Viscosity Disperser Bowtie Pitched Blade | 214530 | 2 HP TEFC motor, air/oil hydraulic lift, stainless steel T304, 80-grit finish, table mount design, mounted on bench, operating range 36�540 rpm (6�90 Hz), 8" three-wing bow-tie blade, NEMA 4X VFD, 3-phase, 60 Hz, 230 V. | STOCK |